Design House 546028 Manuál s instrukcemi Strana 1

Procházejte online nebo si stáhněte Manuál s instrukcemi pro Zdravotnický sortiment Design House 546028. Design House 546028 Instructions / Assembly Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 2
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Your new Design House faucet will give you years of trouble free performance. Thank you for
choosing our product for your home. Please read all of these instructions carefully before
installing your new faucet.
When installing your new faucet, hand tighten the connector nuts, then use one wrench to
anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that
are too tight will reduce the integrity of the system.
Wrap threaded connections (except aerator thread in spout or where o-ring or rubber sealant
are present) with Teflon tape available from your local hardware or plumbing supply store.
Always wrap in a clockwise direction.
IMPORTANT POINTS
SAFETY TIPS
ALWAYS protect your eyes with safety glasses.
Helpful tools to install this faucet:
Teflon tape
(2) crescent wrenches
basin wrench
flashlight
faucet supply tubes
silicon sealer
5. FLUSHING
Place the handle (5A) on the valve body
inverter (5B) and turn the handle (5A) to
the full on mixed position. Turn on the hot
and cold water supply lines and allow the
water to flow from the outlets for one
minute, or until all foreign matter has been
flushed out. Check for leaks. Shut off the
water at the faucet and supply lines.
Remove the handle (5A) and unscrew
the screw (5C).
4. SHOWER ONLY OUTLET
CONNECTIONS
Wrap thread sealant tape around the pipe
threads in a clockwise direction, as shown.
Connect the hot and cold water supply
lines (4A, not included), the shower outlet
pipe (4B, not included) to valve body (4C).
Wrap thread sealant tape around the
threads of the plug (4D), and insert it into
the bottom outlet (4E). Connect the pipe
elbows (4F, not included) to the end of the
pipe, and tighten with a wrench.
Note: a. Be sure to position the body (4C)
correctly in the wall, with the markings "UP"
facing upward.
b. The hot water supply lines go into
the H inlet, and the cold water supply lines
go into the C inlet.
1. Shut off the water supply to the tub and
shower. Verify that the hole sizes and
positions of the holes in the wall are correct:
a. The shower and tub spout outlet holes
should be 1-1/4 in. diameter.
b. The valve access hole should be 6 in.
diameter.
c. The recommended valve depth to the
finished wall is 2 in. min. to 2-1/2 in. max.
Ensure that the valve body (1A) cover is flush
with the finished exterior surface of the wall.
Position the valve body (1A) correctly in the
wall with the "UP" pointing up. The 8 in.
minimum from the valve body to the tub
spout is required for proper operation.
2. Unscrew the screws (2A), and remove
the plaster guard (2B).
3. TUB & SHOWER OUTLET CONNECTIONS
Wrap thread sealant tape around the pipe
threads in a clockwise direction, as shown.
Connect the hot and cold water supply lines
(3A, not included), the shower (3B, not
included) and tub outlet pipes (3C, not included)
to the valve body (3D). Connect the pipe elbows
(3E, not included) to the ends of both pipes, and
tighten with a wrench.
Note: a. Be sure to position the body (3D)
correctly in the wall, with the markings "UP"
facing upward.
b. The hot water supply lines go into the
H inlet, and the cold water supply lines go into
the C inlet.
c. Do not use PEX or CPVC between the
valve and spout.
30 in.
Tub & Shower
8 in. Min.
48 in.
Shower Only
1 1/4 in.
Diameter
1 1/4 in. Diameter
48 in.
Tub & Shower
6 in. Diameter
30 in.
Shower Only
5A
1A
2A
2B
HOT
COLD
3A
3B
3E
3D
3C
HOT
COLD
4A
4B
4F
4C
4D
4E
5C
5B
6. Place the plaster guard (6A) onto the body
(6B) and secure with the screws (6C).
6A
6C
6B
Zobrazit stránku 0
1 2

Shrnutí obsahu

Strany 1 - SAFETY TIPS

Your new Design House faucet will give you years of trouble free performance. Thank you forchoosing our product for your home. Please read all of thes

Strany 2 - CONSUMER PROTECTION WARNING

7. SHOWER FLANGE AND SHOWER ARMINSTALLATIONInsert the long end of the shower arm (7A)through the flange (7B), then wrap threadsealant tape around lon

Komentáře k této Příručce

Žádné komentáře

Allied Telesis AT-FS750/16 Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Netzwerk-Switches Allied Telesis AT-FS750/16.
Wir stellen 1 PDF-Handbücher Allied Telesis AT-FS750/16 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung






Weitere Produkte und Handbücher für Netzwerk-Switches Allied Telesis

Modelle Dokumententyp
Summit 48 Installationsanleitung   Allied Telesis Summit 48 Installation guide, 52 Seiten
AT-8700XL SERIES Installationsanleitung   Allied Telesis AT-8700XL SERIES Install guide, 10 Seiten
AT-8525 Betriebsanweisung   Allied Telesis AT-8525 User guide, 1025 Seiten
Patch 89262-08 Bedienungsanleitung   Patch Release Notes for Patch 89262-08, 32 Seiten
SB251-08 Bedienungsanleitung   Release Notes for Patch SB251-08, 12 Seiten
48Ts/X Bedienungsanleitung   x610 Series, 8 Seiten
AT FH824U AT-FH824U AT-FH824U Bedienungsanleitung   AT-View Plus 2.2 Release Notes, 15 Seiten
AT-x510DP-52GTX Installationsanleitung   Allied Telesis AT-x510DP-52GTX Installation guide, 129 Seiten
Patch 1 PN 613- Installationsanleitung   Allied Telesis Patch 1 PN 613- Installation guide, 19 Seiten
x3100 Series Betriebsanweisung   Allied Telesis x3100 Series User guide, 188 Seiten
AT-FS705L Installationsanleitung     Allied Telesis AT-FS705L Installation guide, 40 Seiten
x600-24Ts-POE Installationsanleitung   Allied Telesis x600-24Ts-POE Installation guide, 112 Seiten
Rapier 16F-FX/MT Spezifikationen   Allied Telesis Rapier 16F-FX/MT Specifications, 65 Seiten
Rapier G6F-MT-RJ Spezifikationen   Allied Telesis Rapier G6F-MT-RJ Specifications, 15 Seiten
AT-DC2552XS Bedienungsanleitung   AT-DC2552XS [Rev E], 6 Seiten
AT-IX5-28GPX Installationsanleitung   Allied Telesis AT-IX5-28GPX Installation guide [en] , 129 Seiten
AT-8900 SERIES Bedienungsanleitung   1 Overview - Allied Telesis, 63 Seiten
AT-8000GS Bedienungsanleitung   AT-S95 Version 2.0.0.24 AT-8000GS Switch, 9 Seiten
C613-02013-00 Betriebsanweisung   Allied Telesis C613-02013-00 User guide, 104 Seiten
AT-9924T/4SP-A-20 Installationsanleitung       Allied Telesis AT-9924T/4SP-A-20 Install guide, 40 Seiten